AUTOOL CT400 Fuel Injector Cleaner and Tester Automobile GDI EFI FSI Ultrasonic Wave Fuel Injector Cleaning Machine 6 Cylinders Petrol Injection Tester for Cars Motorcycles

AUTOOL CT400 Fuel Injector Cleaner & Tester Features: Ultrasonic Cleaning: It sends signals to the injectors through the pulse signal line, using the cleaning fluid with the ultrasonic vibration so as to completely remove the carbon and impurities inside the injectors.Clean Multiple Injectors At The Same Time. GDI Type: AUTOOL CT400 adopts the latest and unique GDI fuel injector drive technology, which can drive 12V, 70V, 120V high pressure fuel injectors. Meanwhile, please don't worry if you can't judge the voltage type of injector, the CT400 will alarm the mismatch voltage, as the CT400 can intelligently determine the required driving voltage of GDI injector. Intelligent Cooling System: The AUTOO CT400 injector cleaner is equipped with a cooling fan and thermal protection with a power of 60w. In case of high temperature during use, the cooling system will start intelligently to avoid damaging the machine due to overheating, thus increasing the service life of the machine. Portable Storage Drawer: 1. The portable storage drawer at the bottom is designed to store various parts for handy use and without leaving a mess on your workbench. Every detail is practical and convenient. 2. AUTOOL CT400 model supports 110V/220V supply voltage, as well as simultaneous cleaning and testing of 6-cylinder injectors; Increase efficiency and save time. You can also optionally test two injectors or four injectors for your different needs. Wide Compatibility: Support GDI, EFI, FSI and other types of fuel injectors as well as support ordinary fuel injectors. The device supports 110V/220V power supply voltage. CT400 Injector Cleaner Tester Function Menu: It is an expert in Injector solutions, featuring 12 injector-specific functions 1. Ultrasonic cleaning: It sends signals to the injectors through the pulse signal line, using the cleaning fluid with the ultrasonic vibration so as to completely remove the carbon and impurities inside the injectors. 2. Idle speed test (0-20ms): Simulate the engine idling speed and test the state of the fuel injector. 3. Medium speed test (0-7.5ms): simulate the engine running at medium speed and test the state of the fuel injector. 4. High-speed test (0-4ms): Simulate the high-speed performance of the engine and test the state of the fuel injector. 5. Acceleration test: Simulate the acceleration state of the car and test the performance of the fuel injector. 6. Shift speed test: Simulate the shifting state of the car and test the working performance of the fuel injector. 7. Leakage test: Test the sealing condition of the fuel injector. 8. Idle dpeed spray ability Test: Simulate the engine idling state and test the spraying performance of the fuel injector. 9. Medium speed spray ability test: Simulate the engine medium-speed state and test the spraying performance of the fuel injector. 10. High-speed spray ability test: Simulate the high-speed state of the engine and test the spraying performance of the fuel injector. 11. Reverse flush: Reverse flush is a way to clean the injectors with the test liquid flowing from the outlet to the inlet of the injector. Reverse flush may remove the dirt inside the injector or the injector Strainer (Only for the top fuel supply injector). 12. No-disassembly cleaning: Direct cleaning without disassembling the injectors, this function is an additional function, which requires special adapters. Injector cleaning agent test liquid and cleaning agent precautions 1. It is forbidden to use corrosive liquids as fuel injection nozzle detection liquid to detect fuel injection nozzles. Corrosive liquids will damage machine seals and fuel injectors. 2. It is forbidden to use a cleaning agent instead of the detection liquid, because the cleaning agent is generally corrosive and will cause damage to equipment and injector seals. 3. It is forbidden to use gasoline instead of cleaning agent or test liquid, which is dangerous and easy to cause safety hazards. 4. Please use absolute ethanol (industrial alcohol) or other non-corrosive liquids as the detection liquid (generally the detection liquids are colorless and transparent, no irritating odor liquid). Parameter: Power supply: AC110V10% / AC220V10% Frequency: 50-60HZ0.5 Relative humidity: lt;85% Ambient temperature: 040 External magnetic field strength: <400A/m No open flames are allowed around Technical parameter Fuel tank capacity: 1500 ml Test tube amount: 140 ml RPM range: 07500 r/min Time range: 09900 times PWM pulse width: 020.0 ms System pressure: 00.55Mpa (adjustable) Timing: 020 minutes adjustable Ultrasonic cleaning power: 60W (intermittent work) Ultrasonic cleaning frequency: 28 KHZ0.5 KHZ Q & A: Q: Oil leak in oil separator assembly: A: leak in oil separator, check whethe stalled "O" ring matches, and check whether it is deformed or damaged. If it doesn't match or is damaged, replace it, The two black adjusting screws must not be over tightened, too tight will also cause oil to leak from the oil separator. Q: The oil pressure drops slowly: A: The oil pressure can't drop to zero in 1-2 minutes, and you can use the hex wrench to adjust the relief valve counterclockwise. Q: The buzzer sounds a long time without oil pressure: A: The machine has a lack of oil alarm function. When the liquid level in the oil tank is insufficient, a sound will be issued and the oil pump and fuel injection nozzle will automatically shut down and return to stop later. In the state, the prompt sound will automatically close after adding enough cleaning liquid. At this time, you need to press the [Run] key to restart the oil pump. Q: "Drain Key" must be pressed twice to completely drain the test solution: A: The solenoid valve of the machine has a function of automatic shutdown in 15 seconds; More liquid in the glass tube may require multiple drains. Q: The amount of cleaning and test solution added: A: When adding cleaning liquid, the cleaning liquid in the ultrasonic box should not exceed the connection port of the fuel injection nozzle; When adding test fluid, the test fluid should not exceed two-thirds of the glass tube screen level. Q: What is a cleaning agent? A: The cleaning agent is used to clean the attachments (carbon deposits) on the fuel injectors. It is generally highly corrosive and flammable. It should be kept away from the fire source and avoid contact with the skin when used. Use it in the ultrasonic cleaning bath of the injector cleaner. Q: What is a test fluid? A: The test fluid is used to test and judge the quality of the fuel injectors. It is a colorless and transparent liquid with no irritating odor, non-corrosiveness, and not easy to emit, but used in the measuring glass of the fuel injector cleaning machine. Buy It With Confidence AUTOOL CT400 has obtained the certificate of conformity, Passed FCC EMC CE ROHS IC SAA CCC GS certification and test. For damage caused by non-human factors, we promise to provide a 3-year warranty, no need to purchase an additional Protection Plan. About AUTOOL AUTOOL has launched a series of professional automotive products, including smoke leak detectors, welding machines, head-up displays, fuel injector testers and cleaners, battery testers, electric hydraulic jacks and engine timing tools, etc. AUTOOL aims to make your car life easier and more convenient.