ZhdnBhnos 6-Head Ultrasonic Mist Maker Fogger Water Fountain Pond Air Humidifier Atomizer w/Power Supply 200W

Ultrasonic Atomization: It Uses Ultrasonic Atomization, the Atomization Process Ultrasonic Waves Will Release a Large Number of Negative Ions, Combined with the Air Floating Soot, Which Can Effectively Remove Smoke, Carbon Monoxide, Bacteria,and Other Harmful Substances and Odors. and Ultrasonic Technology Can Produce Fine Water Mist. If You Drop the Plant Essential Oil into the Water, the Fragrance Will Be Emitted with the Water Mist so That Your Room Is Full of Fragrance. Nozzle Independent Protection: It Has a Fuse for Each Nozzle to Do Independent Protection, Even If a Fog Head Is Broken, the Other Fog Heads Can Continue to Operate. Good Heat Dissipation:It Has a Built-in Copper Plate Heat Sink, Which Can Play a Good Heat Dissipation Effect and Extend Its Service Life. Large Mist Volume:It Has 6 Fogging Heads and Has Excellent Humidification Efficiency, Reaching a Mist Volume of 3kg(6.61lbs) / H. the Effect of Such a Large Amount of Fog Makes You Feel like You Are in a Wonderland. Fast Fogging:Once You Put the AtomizationPlate into the Water and Connect It to the Power Supply, It Will Start Fogging Without Waiting, Saving You Time. Low Noise:It Adopts the Ultrasonic Atomization Method and Has a 1.7mh Safety Frequency, Which Is Beyond the Range of Human Hearing and Harmlessto Humans and Animals. High Safety:ItHasMultipleProtectionFunctions,SuchAsDouble Water Cut-off Protection, Power Reverse Protection, and Overheating Protection. They Add More Security for Your Use. Good Waterproof:Its Fog Headshell Is Made of 304 Stainless Steel, Which Has Good Anti-corrosionand Is Waterproofat the Same Time. Its Power Supply Casing Has an Ip67 Waterproof Rating, so You Can Use It with Confidence. Customer Friendly: Not Only Is This Product Safe, but We Also Have a Buoy for You to Use in Case of Emergencies. When Your Atomization Water Level Is Deep, the Buoy Can Protect the Mist Maker Well and Provide You with a Better Experience. Easy to Replace:It Has a Removable Pressure Ring That You Can Easily Replace by Rotating It for Your Convenience and a Better Atomization Effect. Easy to Clean:You Easily Clean ItWithout Much Effort and Time Because of ItsSmooth Surface.and When You Need to Clean It, You Just Need to Take a Towel or Duster to Wipe off the Dust on It. Customer Service:We Aim to Provide Quality Products and Services. If You Have Any Problems, Please Feel Free to Contact Us. We Will Reply and Solve the Problem for You As Soon As Possible. After the Mist Maker Is Connected to the Power Supply, Please Put It Flat in the Water with the Atomization Head Facing up and Fully Submerged in the Water Before Turning on the Power. When the Mist Maker Is Operating with Power on, Please Avoid Taking out the Mist Maker Upside down to Avoid Damage. The Water Surface Is About 1cm/ 0.394in Above the Water Level Sensor of the Mist Maker, the Atomization Effect Is Appropriate. If the Water Is Too Deep, Please Equip the Buoy. Please Note That the Fog Produced by the Mist Maker Needs to Be Discharged by the Fan to Avoid Fog Stagnation on the Water Surface Resulting in Higher Water Temperature and Shortening the Life of the Mist Maker. When More than One Mist Maker Is in a Container (Interval of Not More than 1m / 39.37in), Each Mist Maker Quality Inspection Shell Needs to Conduct Each Other to Prevent Electrical Corrosion of the Mist Maker Housing and Damage to the Mist Maker. After a Long Time of Work, the Shell and Atomization Piece Surface Will Deposit Scale, Affecting the Service Life and Atomization Effect. It Is Recommended That the Mist Maker Is Gently Scrubbed with a Soft Cloth and Rinsed with Water Once Every Half Month. Please Avoid Damaging the Water Level Switch During the Mist Maker Installation Process, so As Not to Cause the Water Level Switch to Malfunction and Cause the Mist Maker to Go out of Control. This Will Cause the Atomization Piece Dry Burn and Serious Damage to the Mist Maker. When Stop Using the Mist Maker, Please Disconnect the Power and Then Remove the Mist Maker from the Water. The Mist Maker Is Suitable for Atomization of Neutral (Ph=7) Acidic Solutions and Cannot Be Atomized in Strong Acidic or Alkaline Solutions. When You Find That the Fogging Piece Is Broken, Please Immediately Disconnect the Power and Remove the Mist Maker from the Water so That the Water Will Not Enter the Electrical Board and Will Not Cause a Short Circuit. Please Allow the Slight Color Difference Caused by the Shooting Light and 1-3 Cm Error Due to Manual Measurement, and Make Sure You Do Not Mind Before Ordering.